Προσοχή! Στο site μας χρησιμοποιούμε Cookies για στατιστικούς λόγους, κανένα προσωπικό στοιχείο δεν συλλέγεται ή αποθηκεύεται. Μάθετε περισσότερα εδώ. OK

Stepper Motor Driver TMC2208

BIQU, ZZB000150
59-00012208
TMC2208 single-axis stepper motor drive chip, power tube built-in drive current 1.4A peak current 2A, voltage range 4.75V-36V, 256 subdivision; with...
6.80
Διαθέσιμο
+
Προσθήκη στα Αγαπημένα
Διαθεσιμότητα Καταστήματος Αθήνας
Περιορισμένη Διαθεσιμότητα

TMC2208 single-axis stepper motor drive chip, power tube built-in drive current 1.4A peak current 2A, voltage range 4.75V-36V, 256 subdivision; with patented technology spreadCycle high chopper frequency, dcStep, stallGuard2 stall detection technology, CoolStep current dynamic adjustment technology, can save 70% of the energy, StealthChop mute technology.

Flexible microPlyer interpolation unit, the component can provide up to 256 microstep / step resolution, even in the pulse rate is limited system can still be perfect to achieve sinusoidal control; As stealthChop fine music technology is widely used in 3D printing, so These components are also designed to be compatible with existing 3D printer electronics, eliminating the need for costly redesign. Both components have pulse / direction input, can be completely independent operation. The configuration is implemented via digital input.

Κατασκευαστής :
BIQU
MPN:
ZZB000150
Χώρα Προέλευσης:
Κίνα
Max. Current per Channel:
2A
Τύπος Οδηγού:
  • Stepper
  • Interface: Step/Dir
  • Configuration: CFG Pins or UART
  • Native Microsteps: up to 1/256
  • microPlyer Microsteps: 1/256
  • Logic Voltage (VIO): 3-5V
  • Motor Voltage (VM): 5.5-36V
  • Motor Phase Current max: 1.2A RMS, 2.0A Peak
  • Internal V- Regulator: enabled
  • RDSon: <=0.3 Ohm
  • stealthChop (quiet): Yes
  • spreadCycle: Yes
  • coolStep: No
  • stallGuard: No
  • dcStep: No
  • UART configuration interface (9600-500k Baud)
  • Power tube built-in drive current 1.4A ,peak current 2A, voltage range 4.75V-36V
  • Up to 256 native microsteps (without interpolation)
  • CoolStep ™ current dynamic adjustment technology, can save 70% of the energy
  • stealthChop2 - faster motor acceleration/deceleration than stealthChop
  • dcStep ™, stallGuard2 ™ stall detection technology
  • Automatic stealthChop and spreadCycle switchover depending on velocity
  • Hardware compatible with StepStick and Pololu A4988 Stepper Driver
  • Components on bottom PCB side for better heat emission
  • Automatic standby current reduction
  • SteaClthhop mute technology
  • spreadCycle - highly dynamic motor control chopper
  • 20,3x15.5x11.3mm (without heatsink)
Pin Function
  Power Supply
GND Ground
VM Motor Supply Voltage
VIO Logic Supply Voltage
  Motor Outputs
M1A Motor Coil 1
M1B Motor Coil 1
M2A Motor Coil 2
M2B Motor Coil 2
  Control Inputs
STEP Step-Signal Input
DIR Direction-Signal Input
  TMC2208
EN Enable Motor Outputs: GND=on, VIO=off
MS1 Step-Configuration
MS2 Step-Configuration
PDN UART and Auto Power Down Control: GND=on, VIO=off
CLK Clock Input
DIAG Diagnostics Output
INDEX Index Output
VREF Analog Reference Voltage

Interface Resources


Wiring Diagram

TMC2208-wiring-diagram

Οι φωτογραφίες των προϊόντων μπορεί να διαφέρουν απο την πραγματικότητα. Προσπαθούμε να παρουσιάσουμε το προϊόν όσο καλύτερα γίνεται.