ΔΩΡΕΑΝ ΜΕΤΑΦΟΡΙΚΑ για παραγγελίες άνω των 85.00 έως 2kg

Capricorn XS Series PTFE Bowden Tubing for 1.75mm Filament

από CAPRICORN
One Meter of our flagship PTFE Tubing, enhanced with a proprietary blend of high performance additives. 1.9mm inner, 4mm outer diameter for 1.75mm...
26-00023919
Ογκομετρικό βάρος: 0.01kg
Εγγύηση: Ως εξάρτημα, δεν καλύπτεται
Κατασκευαστής: CAPRICORN
Part Number: 4004200006
Εξαντλημένο
Το προϊόν δεν είναι διαθέσιμο
Χαμηλό απόθεμα στο κατάστημα
14.80
Χωρίς ΦΠΑ 11.94

Συναινώ ώστε η εταιρεία (GRobotronics) να προσθέσει την διεύθυνση ηλεκτρονικού μου ταχυδρομείου στην λίστα ώστε να λάβω ενημέρωση όταν το προϊόν θα είναι ξανά διαθέσιμο. Μόλις το προϊόν γίνει ξανά διαθέσιμο θα λάβω αυτόματα ενημέρωση στο email αυτό και αμέσως θα αφαιρεθεί από την συγκεκριμένη λίστα.

Το email σου θα χρησιμοποιηθεί αποκλειστικά για τον σκοπό αυτό και καμία άλλη ενημέρωση δεν θα λάβεις. Θα είναι ορατό μόνο από συγκεκριμένους εξουσιοδοτημένους υπαλλήλους της εταιρείας.

Έχετε το δικαίωμα σε περίπτωση κατά την οποία θεωρείτε ότι η επεξεργασία που γίνεται δεν είναι σύμφωνη με τα ανωτέρω να αναζητείτε την προστασία της Αρχής Προσωπικών Δεδομένων και να ζητήσεις να διαγράψουμε ή να μεταβάλλουμε τα δεδομένα σου. Είμαστε υποχρεωμένοι σύμφωνα με τον κανονισμό της ΕΕ για την Προστασία των Γενικών Προσωπικών Δεδομένων να σε ενημερώσουμε για αυτό το δικαίωμα. Έχετε την δυνατότητα να επικοινωνείτε όποτε επιθυμείτε με την εταιρεία ώστε να ενημερωνόσαστε σχετικά με τα προσωπικά σας δεδομένα στο email [email protected]

ΑΓΑΠΗΜΕΝΑ ΣΥΓΚΡΙΣΗ

ΠΕΡΙΓΡΑΦΗ

One Meter of our flagship PTFE Tubing, enhanced with a proprietary blend of high performance additives. 1.9mm inner, 4mm outer diameter for 1.75mm filaments.

This is, hands down, the single best PTFE Bowden tubing you can buy for your home 3D printer.

Guaranteed to always be the right diameter, and perfectly round. Print flexible filaments without the binding up that happens with over-diameter tubes.

Each meter of tubing comes with one Capricorn sticker to decorate your printer.

ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

Εγγύηση:
Ως εξάρτημα, δεν καλύπτεται
Κατασκευαστής
:
CAPRICORN
Part Number:
4004200006
Μικτό Βάρος:
0.006kg
Συμβατότητα Εκτυπωτή:
  • CR-20 Pro
Αναλώσιμα Υλικά 3D Εκτυπωτή:
Teflon Tube
Συμβατότητα Extruder:
  • CR10 (MK8 Hotend)

ΕΠΙΠΛΕΟΝ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

  • Additives: Blue Color and Secret High Lubricity Additive Mixture
  • Best For Chunky Filaments: YES
  • Best For Flexible Filaments: YES
  • Can See Through: NO
  • Pulling Friction: 0.8
    • Pulling Friction is calculated as the average force required to pull 1.2 meters of 1.75mm PLA filament through 1 meter of tubing at a constant speed, relative to 1 meter of cheap white reference tubing. Note that although we observed the friction of the TL series to be about the same or even slightly lower than our XS series, it also has a larger internal diameter.
  • Color: Dark Blue
  • Density (kg/m3): 2300 +/-100
  • Hardness: 60-65
  • Inner Diameter (mm): 1.90 +/- 0.05
  • Linear Thermal Expansion at 250°C: 2.2-3.3%
  • Material: Highest Quality Pure Virgin PTFE
  • Melting Point (°C): up to 340
    • Temperatures were approximated by heating samples of all tubing simultaneously, observing how quickly each one began to deform. Printer failures may happen at significantly lower temperatures.
  • Outer Diameter: 3.95 +/- 0.05
  • Roundness (ϵ): < 0.1
  • Stiffness: Medium High
    • Other Bowden tubes may vary significantly in stiffness, depending on the material from which they're made. Our tubing generally tends to be more flexible than most, with the TL being more flexible than XS.
  • Thermal Conductivity (W/m-k): 0.25
  • Wear Rate (gm/s): 0.01
  • Young's Modulus (GPa): 0.53
    • Young's Modulus (YM) is the measure of elasticity of the material. Our XS Series additives give the PTFE a slightly greater YM than the TL Series.

Cross Section Dimension

  • ID: 1.95mm ± 0.05mm
  • OD: 4.0mm
  • Length: 1 Meter

ΔΥΝΑΤΟΤΗΤΕΣ

Capricorn XS Series PTFE Tubing VS Original PTFE Tubing

1.9mm ± 0.05mm Inner Diameter Reduces the "wiggle room," or buckling, inside the tube, allowing you to print flexible filaments even on the longest Bowden systems.