ΔΩΡΕΑΝ ΜΕΤΑΦΟΡΙΚΑ για παραγγελίες άνω των 85.00 έως 2kg

Stepper Motor Driver TMC2209 V2.0

από OEM
TMC2209 have all function of TMC2208, can completely replace tmc2208. At the same time, TMC2209 have better heat dissipation, support bigger current,...
59-00012244
Ογκομετρικό βάρος: 0.01kg
Εγγύηση: Ως εξάρτημα, δεν καλύπτεται
Κατασκευαστής: OEM
Part Number: TMC2209
Χώρα Προέλευσης: Κίνα
Διαθέσιμο
Αποστολή σε 24 ώρες
Διαθέσιμο στο φυσικό κατάστημα
6.80
Χωρίς ΦΠΑ 5.48
+
Τιμές βάση ποσότητας (Λιανική - Χονδρική):
Ποσότητα 10+
Τιμή 5.44

ΣΥΝΔΥΑΣΕ ΤΟ ΜΕ

ΠΕΡΙΓΡΑΦΗ

TMC2209 have all function of TMC2208, can completely replace tmc2208. At the same time, TMC2209 have better heat dissipation, support bigger current, support sensorless-homing function.

Features:

  • Ultra quiet
  • Large heat sink,good heat dissipation
  • Support sensorless-homing function.
  • Support uart mode by set jumper caps instead of welding on mks gen_l V2.0,skr1.3/1.4,mks sgen_l.

 

NOTES

  • Pay attention to the connection direction,do not reverse it.
  • The motor direction is opposite to that of A4988 and DRV8825, please adjust the firmware or adjust the motor wiring if you want to change A4988.
  • Dir/step mode used in the printer control board, please pay attention to set the jumper cap MS1 MS2.

ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

Εγγύηση:
Ως εξάρτημα, δεν καλύπτεται
Κατασκευαστής
:
OEM
Part Number:
TMC2209
Μικτό Βάρος:
0.007kg
Χώρα Προέλευσης:
Κίνα
Max. Current per Channel:
2A
Τύπος Οδηγού:
  • Stepper

ΕΠΙΠΛΕΟΝ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

  • Default current: 0.88A
  • Recommend current: 1.72A (at most)
  • Max current: 2A
  • Logic voltage: 3.3V/5V
  • Input voltage: 5.5 - 28V
  • Microstep: Up to 1/256
  • Mode:
    • DIR/STEP
    • UART

ΔΥΝΑΤΟΤΗΤΕΣ

Microstep set:

Microstep setting
M0 M1 STEP
GND GND 8
VCC_IO GND 32
GND VCC_IO 64
VCC_IO VCC_IO 16

Driver current regulation:

  • Verf measures the voltage of Gnd and potentiometer middle.
  • Please DO NOT connect the motors when measuring the voltage, or it's easy to burn the drive.
  • Please connect the power supply when measuring voltage as well, do not connect only the USB power.
  • Please pay special attention to the direction, do not insert wrongly!

Uart mode:

Uart mode can be used on mks gen_l(v2.x),mks sgen_l,skr1.3/1.4 by set jumper cap like below:

  • MKS Sgen_L / MKS Gen_L:

  • SKR 1.3/1.4:

Sensorless-homing function:

Used on mks gen_l(v2.x),mks sgen_l,skr1.3/1.4 by set jumper cap like below:

  • MKS Sgen_L / MKS Gen_L:

  • MKS Robin E3D:

  • SKR 1.3/1.4:

 

ΑΡΧΕΙΑ

ΒΙΝΤΕΟ

MKS TMC2209 V2.0 Use tutorial: DIR/Step and Uart mode (sensorless homing)