ΔΩΡΕΑΝ ΜΕΤΑΦΟΡΙΚΑ για παραγγελίες άνω των 85.00 έως 2kg

Φορτιστής για Μπαταρίες 2x 18650 με Step-Up 5V - USB

από OEM

Αυτός ο φορτιστής για μπαταρίες 2x 18650 χρησιμοποιείται για τη φόρτιση και την τροφοδοσία μιας πλακέτας επέκτασης Arduino, ESP8266, ESP32 μέσω της εξόδου USB ή απευθείας χρησιμοποιώντας τις δέκα εξόδους (pin συγκόλλησης) που είναι διαθέσιμες σε κάθε πλευρά της πλακέτας (5V ή 3V). Έχει κύκλωμα φόρτισης, προσέξτε τους πόλους της μπαταρία κατά την εγκατάσταση, μην αντιστρέψετε (δεν προστατεύεται από αντίστροφη πολικότητα). Τέσσερις ενδεικτικές λυχνίες LED υποδεικνύουν την εξέλιξη της φόρτισης της μπαταρίας (1<25%, 2<50%, 3<75% 4=100%).

19-00015796
Ογκομετρικό βάρος: 0kg
Εγγύηση: Ως εξάρτημα, δεν καλύπτεται
Κατασκευαστής: OEM
Χώρα Προέλευσης: Κίνα
Διαθέσιμο
Αποστολή σε 24 ώρες
Διαθέσιμο στο φυσικό κατάστημα
7.90
Χωρίς ΦΠΑ 6.37
+
Τιμές βάση ποσότητας (Λιανική - Χονδρική):
Ποσότητα 10+
Τιμή 6.32

ΠΕΡΙΓΡΑΦΗ

This 18650 battery shield is used to charge and power an Arduino, ESP8266, ESP32 expansion board via the USB output (type A) or directly using the 6 outputs (soldering pin) available on each side of the board (5V or 3V). The shield has a charging circuit (not protected against polarity inversions). Four LEDs indicates the progress of the battery charge (1<25%, 2<50%, 3<75% 4=100%).

According to the product designation, this card seems to power a mini PC Raspberry Pi type. It is more an optimization of keywords to be visible in the search results than a real power solution. In theory, it should also allow to power the Raspberry Pi and all other mini PCs (Orange Pi, Banana Pi, Odroid …) that have a USB OTG port. Be careful however to buy a high capacity LiFePO battery. The card has no output to measure the battery charge level. It will therefore be necessary to be careful to measure the service life for a complete charge in order to avoid any sudden stop of the system. SD cards do not support this kind of joke and do not hesitate to remind us at the next start: lol: At the risk of being pampered, remember to regularly backup your SD cards. Also be careful to stop the system before turning off the power using a microswitch on the shield. There is no return Raspberry Pi, the stop is immediate.

The shield has a fairly basic charge control circuit. It is clear to stay polarity. Any inversion of polarity may cause the destruction of the charging circuit. The board has a micro USB connector to charge the battery.

We can feed a development card or any device with a USB port. For this, we have a type A USB output. The maximum intensity delivered is not indicated. It is probably 4A as the side connectors. We also have 3 connectors to deliver 3V up to 1A and 3 connectors to deliver 5V up to 2A. The 6 connectors are on each side of the board. It will directly solder the power supply or solder a header at a pitch of 2.54mm beforehand.

 

ΣΗΜΕΙΩΣΕΙΣ

  • This module is suitable for 18650 battery only.
  • This module can be powered or for raspberry pi and sensor at the same time.
  • This module output current up to 2A.
  • This product does not contain 18650 battery installation, be careful of the battery positive and negative when install, do not reverse. Please follow the + - direction on the PCB and do not follow the positive and negative directions on the battery holder.

ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

Εγγύηση:
Ως εξάρτημα, δεν καλύπτεται
Είδος Περιφερειακού:
  • Step-Up
Κατασκευαστής
:
OEM
Τάση Εισόδου:
5-8Volt
Τάση Εξόδου:
5Volt
Ένταση Εξόδου:
4Amp
Μικτό Βάρος:
0.001kg
Χώρα Προέλευσης:
Κίνα
Χημική Σύσταση:
  • Lithium-Ion (Li-Ion)
Τύπος Μπαταρίας:
  • 18650
Υποδοχές Mπαταριών:
2

ΕΠΙΠΛΕΟΝ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

  • Power supply: 5 to 8V via micro USB port up to 0.5A
  • Input ports:
    • microUSB
    • type-C
  • Output power:
    • 5V via USB Type A port
    • 5 connectors to deliver 3V up to 1A
    • 5 connectors to deliver 5V up to 3A
  • Misc:
    • LEDs for the state of charge (1<25%, 2<50%, 3<75% 4=100%)
  • Battery protection (overcharging or over-discharging). Attention, no protection in case of reverse polarity
  • Dimensions: 110x49x16mm
  • Weight: 40g