+302118004320
Greek (GR)
0Στο Καλαθι

Φορτιστής για Μπαταρία 18650 με Step-Up 5V - USB

19-00019848
ΚατασκευαστήςOem
Διαθέσιμο
Αποστολή σε 24 ώρες
€480
Ποσοτικές εκπτώσεις:
Ποσότητα
10+
Τιμή
€3.84
+ −
Αγαπημένα
Κάνε μια ερώτηση
Gropbotronics Store Availability
Διαθεσιμότητα Καταστημάτων
Πληρωμή & Μεταφορικά

This 18650 battery shield is used to charge and power an Arduino, ESP8266, ESP32 expansion board via the USB output (type A) or directly using the 6 outputs (soldering pin) available on each side of the board (5V or 3V). The shield has a charging circuit (not protected against polarity inversions).

According to the product designation, this card seems to power a mini PC Raspberry Pi type. It is more an optimization of keywords to be visible in the search results than a real power solution. In theory, it should also allow to power the Raspberry Pi and all other mini PCs (Orange Pi, Banana Pi, Odroid …) that have a USB OTG port. Be careful however to buy a high capacity LiFePO battery. The card has no output to measure the battery charge level. It will therefore be necessary to be careful to measure the service life for a complete charge in order to avoid any sudden stop of the system.

The shield has a fairly basic charge control circuit. It is clear to stay polarity. Any inversion of polarity may cause the destruction of the charging circuit. The board has a micro USB connector to charge the battery.

We can feed a development card or any device with a USB port. For this, we have a type A USB output. The maximum intensity delivered is not indicated. It is probably 4A as the side connectors. We also have 3 connectors to deliver 3V up to 1A and 3 connectors to deliver 5V up to 2A. The 6 connectors are on each side of the board.

 

ΣΗΜΕΙΩΣΕΙΣ

  • This module is suitable for 18650 battery only.
  • This module can be power a raspberry pi and sensor at the same time.
  • This module output current up to 2A.
  • This product does not contain 18650 battery installation, be careful of the battery positive and negative when install, do not reverse. Please follow the + - direction on the PCB and do not follow the positive and negative directions on the battery holder.

  • Power supply: 5 to 8V via micro USB port up to 0.5A
  • Output power
    • 5V via USB Type A port
    • 3 connectors to deliver 3V up to 1A
    • 3 connectors to deliver 5V up to 2A
  • Misc:
    • 1 USB output
    • LED for the state of charge (green=battery charged, red=charging)
  • Battery protection (overcharging or over-discharging). Attention, no protection in case of reverse polarity
  • Dimensions: 106x29x17mm
Κατασκευαστής
Oem
Τάση Εισόδου
5-8 Volt
Τάση Εξόδου
5 Volt
Ένταση Εξόδου
3 Amp
Εγγύηση
Ως εξάρτημα, δεν καλύπτεται
Καθ. Βάρος
0.025kg
Χημική Σύσταση
  • Lithium-Ion (Li-Ion)
Τύπος Μπαταρίας
  • 18650
Υποδοχές Mπαταριών
1
Βρες Παρόμοια
  • Προτείνουμε επίσης