ΔΩΡΕΑΝ ΜΕΤΑΦΟΡΙΚΑ για παραγγελίες άνω των 85.00 έως 2kg

Kitronik :MOVE Motor Klaw Kit

από Kitronik
Το :MOVE Motor Klaw προσφέρει μια διασκεδαστική και εύκολη εγκατάσταση στο Kitronik :MOVE Motor buggy για microbit. Έχει σχεδιαστεί προσεκτικά ώστε να έχει τη δυνατότητα τοποθέτησης τόσο κάθετα όσο και οριζόντια με ένα παξιμάδι. Περιλαμβάνονται δύο τύποι Klaw attachments για κάθε μία από αυτές τις εκδόσεις.
83-00005703
Κατασκευαστής: Kitronik
Part Number: 5696
Χώρα Προέλευσης: Ηνωμένο Βασίλειο
Διαθέσιμο
Αποστολή σε 24 ώρες
Χωρίς απόθεμα στο φυσικό κατάστημα
9.90
Χωρίς ΦΠΑ 7.98
+

ΣΥΝΔΥΑΣΕ ΤΟ ΜΕ

ΠΕΡΙΓΡΑΦΗ

The :MOVE Motor Klaw provides a fun and easy to install addition to the Kitronik :MOVE Motor buggy for microbit. It has been carefully designed to have the ability to fit both vertically and horizontally with one bolt. Included are two types of Klaw attachments for each of these builds.

It is controlled by a low voltage servo which is included, this servo is used to open and close the Klaw. The voltage supply and control signal are all from the :MOVE Motor via the pin headers, simply connect the servo lead onto the pin headers.

The :MOVE Motor Klaw can be coded with MakeCode or with MicroPython and we have produced online guides to walk you through both. These guides can be found in the list of resources below along with the build instructions. 

 

ΤΟ ΠΑΚΕΤΟ ΠΕΡΙΕΧΕΙ

Requires:

ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

Συμβατό Micro:bit:
  • V1
  • V2
Κατασκευαστής
:
Kitronik
Part Number:
5696
Χώρα Προέλευσης:
Ηνωμένο Βασίλειο
Breadboard Friendly:

ΕΠΙΠΛΕΟΝ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

  • Easily add a gripping Klaw to :MOVE Motor.
  • Servo powered opening and closing with the servo included as a part of the kit.
  • Fit to :MOVE motor either horizontally or vertically.
  • Easy to assemble.
  • Code it with MakeCode or with MicroPython.
  • Dimensions:
    • Overall Length: 115mm.
    • Closed Width: 70mm.
    • Open Width: 125mm.
    • Height w/servo: 38mm.

ΒΙΝΤΕΟ

Kitronik :MOVE Motor for micro:bit Klaw Kit

The :MOVE Motor Klaw provides a fun and easy to install addition to the Kitronik :MOVE Motor buggy for microbit. It has been carefully designed to have the ability to fit both vertically and horizontally with one bolt. Included are two types of Klaw attachments for each of these builds. It is controlled by a low voltage servo which is included, this servo is used to open and close the Klaw. The voltage supply and control signal are all from the :MOVE Motor via the pin headers, simply connect the servo lead onto the pin headers. The :MOVE Motor Klaw can be coded with MakeCode or with MicroPython and we have produced online guides to walk you through both. These guides can be found in the list of resources below along with the build instructions.

ΠΡΟΤΕΙΝΟΥΜΕ ΕΠΙΣΗΣ