Αρχική Σελίδα/Ρομποτική/Raspberry Pi/Raspberry Pi Πρόσθετα (HATs)/Waveshare RS485 HAT - 2-Channel Isolated

Waveshare RS485 HAT - 2-Channel Isolated

Κωδικός:

31-00017221

Part Number: 2-CH RS485 HAT

ΚατασκευαστήςWaveshare Part Number2-CH RS485 HAT

Διαθέσιμο

Αποστολή σε 24 ώρες

€22⁹⁰

Ποσοτικές εκπτώσεις:

Ποσότητα

10+

Τιμή

€20.61

+ −

Κάνε μια ερώτηση

Διαθεσιμότητα Καταστημάτων

Πληρωμή & Μεταφορικά

Περιγραφή
Χαρακτηριστικά

2-Channel Isolated RS485 Expansion HAT for Raspberry Pi, SC16IS752+SP3485 Solution, with Multi Onboard Protection Circuits

This is a 2-channel isolated RS485 expansion HAT designed for Raspberry Pi, adopts the SC16IS752+SP3485 solution, with embedded protection circuits such as power supply isolation, ADI magnetical isolation, and TVS diode, etc.

It is easy to control the 2-channel RS485 for auto transceiving via SPI interface. Due to its fast communication, stability, reliability, and safety, it is an ideal choice for fields like industrial automation.

ΤΟ ΠΑΚΕΤΟ ΠΕΡΙΕΧΕΙ

2-CH RS485 HAT x1
2x20PIN female pinheader x1
RPi screws pack (2pcs) x1

2-CH RS485 HAT on board resource

SC16IS752 UART expansion chip
ADUM1412 digital isolator
PC817 optocoupler
SP3485 RS485 transceiver
B0505LS power supply isolation module
RT9193-33 power chip
SMAJ12CA transient suppress diode array
Auto-recovery fuse
Status indicator
PWR: power indicator
RXD/TXD: UART transceiving indicator
Raspberry Pi GPIO connector: for connecting Raspberry Pi
RS485 terminal
MCU control header: for connecting host control boards like Arduino
120Ω terminal resistor switch
Interrupt pin switch
Operating mode selection
Half-auto: A=0, B=1
Full-auto: A=1, B=0

UART expansion chip: SC16IS752
RS485 transceiver: SP3485
Communication interface: SPI
Data rate: 300 ~ 921600 bps
Operating voltage: 3.3V / 5V
Dimensions: 65x56.5mm
Mounting hole size: 3.0mm

Pinouts

PIN	RASPBERRY PI (BCM)	DESCRIPTION
VCC	5V	3.3V/5V power supply
GND	GND	Ground
SCK	P21 (SPI1 SCLK)	SPI clock input
MOSI	P20 (SPI1 MOSI)	SPI data input
MISO	P19 (SPI1 MISO)	SPI data output
CS	P18 (SPI1 CS)	SPI chip select
IRQ	P24	Interrupt output
EN1	P27	Channel 1 TX/RX enable: high for TX, low for RX
EN2	P22	Channel 2 TX/RX enable: high for TX, low for RX

Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards
Adopts SC16IS752+SP3485 dual chip combination, converts SPI to RS485, data rate up to 921600bps
Allows transceiving data manually or automatically, configured by DIP switch
Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit, lightning-proof & anti-electrostatic

Onboard auto-recovery fuse and protection diodes, ensures the current/voltage stable outputs, provides over-current/over-voltage proof, improves shock resistance
Onboard LEDs for indicating the power and transceiver status
Breakout SPI control pins, for connecting with host control boards like Arduino
Comes with development resources and manual (examples in C and Python)