ΔΩΡΕΑΝ ΜΕΤΑΦΟΡΙΚΑ για παραγγελίες άνω των 85.00 έως 2kg

I2C to 16Bit Parallel IO Expander - PCF8575

από OEM
This module adds a 3.3V LDO and level shifter to the typical breakout for the PCF8575 GPIO Expander. The module connects via the I2C bus to your...
19-00012895
Ογκομετρικό βάρος: 0kg
Εγγύηση: Ως εξάρτημα, δεν καλύπτεται
Κατασκευαστής: OEM
Χώρα Προέλευσης: Κίνα
Εξαντλημένο
Το προϊόν δεν είναι διαθέσιμο
Χωρίς απόθεμα στο φυσικό κατάστημα
3.60
Χωρίς ΦΠΑ 2.90

Συναινώ ώστε η εταιρεία (GRobotronics) να προσθέσει την διεύθυνση ηλεκτρονικού μου ταχυδρομείου στην λίστα ώστε να λάβω ενημέρωση όταν το προϊόν θα είναι ξανά διαθέσιμο. Μόλις το προϊόν γίνει ξανά διαθέσιμο θα λάβω αυτόματα ενημέρωση στο email αυτό και αμέσως θα αφαιρεθεί από την συγκεκριμένη λίστα.

Το email σου θα χρησιμοποιηθεί αποκλειστικά για τον σκοπό αυτό και καμία άλλη ενημέρωση δεν θα λάβεις. Θα είναι ορατό μόνο από συγκεκριμένους εξουσιοδοτημένους υπαλλήλους της εταιρείας.

Έχετε το δικαίωμα σε περίπτωση κατά την οποία θεωρείτε ότι η επεξεργασία που γίνεται δεν είναι σύμφωνη με τα ανωτέρω να αναζητείτε την προστασία της Αρχής Προσωπικών Δεδομένων και να ζητήσεις να διαγράψουμε ή να μεταβάλλουμε τα δεδομένα σου. Είμαστε υποχρεωμένοι σύμφωνα με τον κανονισμό της ΕΕ για την Προστασία των Γενικών Προσωπικών Δεδομένων να σε ενημερώσουμε για αυτό το δικαίωμα. Έχετε την δυνατότητα να επικοινωνείτε όποτε επιθυμείτε με την εταιρεία ώστε να ενημερωνόσαστε σχετικά με τα προσωπικά σας δεδομένα στο email [email protected]

ΑΓΑΠΗΜΕΝΑ ΣΥΓΚΡΙΣΗ

ΣΥΝΔΥΑΣΕ ΤΟ ΜΕ

ΠΕΡΙΓΡΑΦΗ

This module adds a 3.3V LDO and level shifter to the typical breakout for the PCF8575 GPIO Expander.

The module connects via the I2C bus to your Microcontroller and offers I2C address selection by closing solder jumpers on the bottom side (base address is 0x20).

You can either use it on 3.3V or 5V thanks to its on-board LDO and level shifter.

The VDD pin is the power supply for 5V, the VCC pin is the 3.3V output voltage of the LDO. If you use it as 5V device, you supply 5V on VDD. If you use it as 3.3V device, you supply 3.3V to the VCC pin and close the solder jumper VCC-VDD on the bottom side. In a mixed mode, with 5V GPIO ports but connected to a 3.3V Microcontroller, you supply 5V to VDD but leave the VCC-VDD jumper open.

ΣΗΜΕΙΩΣΕΙΣ

  • Pin header requires soldering

 

ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

Εγγύηση:
Ως εξάρτημα, δεν καλύπτεται
Κατασκευαστής
:
OEM
Μικτό Βάρος:
0.003kg
Χώρα Προέλευσης:
Κίνα

ΕΠΙΠΛΕΟΝ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

  • For Arduino available library: PCF8575
  • Working voltage: 2.5 - 5.5VDC
  • Output current: 100mA combined (max. 20mA per channel)
  • Output current source: 1mA max
  • Output current sink: 25mA max
  • I2C address: 0x20(default), can be modified by soldering A1 and A2 selection pads.
  • 16 individually addressable pins.
  • Each pin configurable for input or output.
  • Open-drain interrupt output pin for input change interrupt.
  • Great for Arduino UNO R3 and other MCU to control simple relay, buzzer, button, led.

ΑΡΧΕΙΑ