Σημαντική ενημέρωση: Προτείνουμε αλλαγή κωδικού για την ασφάλειά σας (οι κωδικοί χρησιμοποιούν πολύ ασφαλή μέθοδο κρυπτογράφησης)

Στις 22/5 σημειώθηκε μη εξουσιοδοτημένη πρόσβαση στο κατάστημά μας. Μάθετε περισσότερα εδώ.

Αρχική Σελίδα/Ρομποτική/Αισθητήρες/Χώρου / Απόστασης/Microwave Radar Sensor - RCWL-0516

Microwave Radar Sensor - RCWL-0516

Κωδικός:

19-00018968

ΚατασκευαστήςOEM

Διαθέσιμο

Αποστολή σε 24 ώρες

€1⁸⁰

Ποσοτικές εκπτώσεις:

Ποσότητα

10+

100+

Τιμή

€1.44

€1.26

+ −

Κάνε μια ερώτηση

Διαθεσιμότητα Καταστημάτων

Πληρωμή & Μεταφορικά

Περιγραφή
Χαρακτηριστικά

This sensor module has been designed as an alternative to the common PIR motion sensors widely used in burglar alarms and security lights. Like the PIR sensor, this sensor also detects only movements within its detection range. But instead of sniffing the black body radiation from a moving person, this sensor uses a “microwave Doppler radar” technique to detect moving objects.

The module has the characteristics of high sensitivity, high induction distance, high reliability, large induction angle, wide power supply voltage range, etc. it is widely used in various kinds of human body induction lighting and alarm and so on.

This mini doppler radar sensor module is equipped with supporting DC 4-28V wide voltage. This is a mini radar motion sensor module is equipped with RCWL-9196 chip based on the doppler microwave induction technology. It will automatically comtinuously output the high level TTL signel when there is motion. 360 degree no blind angle detection and maximum 7m sensoring distance with adjustable delay time and sensitivity.

It has a sensitivity range of ~7 meters. When triggered, its TTL-level output (OUT) pin will switch from LOW (0 V) to HIGH (3.3 V) for a finite time (2 to 3 s) before returning to its idle (LOW) state.

It is perfect for DIY microwave motion sensor light switch, human sensor toys, smart security devices, etc.

ΣΗΜΕΙΩΣΕΙΣ

The right ahead of induction side should’t place any metal to block.
The front/back side should reserve more than 1cm space Module and installation carrier

Operating Voltage: 4-28V
Operating Current: 2.8mA (typical), 3mA (max)
Detection Distance: 5-9m
Transmitting Power: 20mW (typical), 30mW (max)
Output Voltage: 3.2-3.4V
Output Voltage Driving Capacity: 100mA
Trigger Way: repeat trigger
Output Control Low Level: 0V
Output Control High Level: 3.3V
Operating Temperature: -20~80 celsius
Storage Temperature: -40~100 celsius
Dimensions: 36x17.5x3mm

Adjustment Part Introduction:

C-TM Adjust repeat trigger time,default trigger time is 2s;increasing capacitor’s capacity will make repeat trigger time longer;and actual counting trigger time can operate as below: Stick capacitor on C-TM,test 9196 3-pin frequency F,repeat trigger time T=(1/f)*32768
R-GN Detection distance adjustment;connect with resistor and detection distance will become shorter;if not connect,detection distance is 7m;if connect with 1M ohm resistor,detection distance is 5m
R-CDS Internal VCC parallel connect with internal 1M ohm resistor to CDS pin (that is 196 9-pin) by R-CDS ,CDS connects with photoresistor,you can close detection function at night

Pin Definition:

3V3:3V3 power output
GND:ground
OUT:control output;when detect moving objects,it will output high level
VIN:input voltage,4-28V
CDS:enable control chip,lower than 0.7V,OUT will output low level all the time

Equipped with RCWL-9196 chip supporting 4-28V wide voltage input, high level signal output when detecting the motion with active repeat trigger
360 degree no blind angle detection with 5-7m deteciting distance, the detection not affected by the surroundings, better performance than the IR sensor

Support night detecting function turn on /off, adjustable repeat trigger time and detecting distance by add the SMD components to the corresponding pins
Working Voltage: DC 4-28V, Board Size: 35.9 X 17.3mm/1.41 X 0.68inch