+302118004320
Greek (GR)
0Στο Καλαθι

RF Nano Compatible V3.0 - NRF24L01

19-00018965
ΚατασκευαστήςOem
Διαθέσιμο
Αποστολή σε 24 ώρες
€1680
Ποσοτικές εκπτώσεις:
Ποσότητα
10+
Τιμή
€13.44
+ −
Αγαπημένα
Κάνε μια ερώτηση
Gropbotronics Store Availability
Διαθεσιμότητα Καταστημάτων
Πληρωμή & Μεταφορικά

The Nano Board has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers. The ATmega328P provide UART TTL (5V) serial communication, which is available on digital pins 0 (RX) and 1 (TX). An FTDI FT232RL on the board channels this serial communication over USB and the FTDI drivers (included with the Arduino software) provide a virtual com port to software on the computer. The Arduino software includes a serial monitor which allows simple textual data to be sent to and from the Arduino board. The RX and TX LEDs on the board will flash when data is being transmitted via the FTDI chip and USB connection to the computer (but not for serial communication on pins 0 and 1). A SoftwareSerial library allows for serial communication on any of the Nano’s digital pins. The ATmega328P also support I2C (TWI) and SPI communication. The Arduino software includes a Wire library to simplify use of the I2C bus. To use the SPI communication.

  • Creative products, RF-Nano-Board: Upgraded nano board for arduino, The main chip is ATMEGA328P-MU QFN32,the latest bootloader (Arduino IDE 1.8.8) was burned down. It is fully compatible with the common nano board. RF-Nano-Board is PIN-PIN with Arduino Nano V3.0, and share the same codes.
  • More convenient for application: The RF-Nano-Board integrates a NRF24L01+ module with arduino nano v3.0 board, which is very convenient for 2.4G wireless connect application.
  • High quality material and Technology: We used high quality PCB original material and Immersion Gold Technology to make sure every board has smooth edge and more reliable.
  • Super small volume design, more convenient to use: The PCB size is only 48x19mm, the pin is fully compatible with Nano V3.0, No Soldering needed. The micro usb port is more convenient to use.
  • Complete Information reference: RF-Nano-Board using CH340 chip to UART, you can download mac, windows, linux three system drivers, datasheets and schematics and other informations from here, we provide quick and free support.

 

ΣΗΜΕΙΩΣΕΙΣ

  • Please use Arduino IDE 1.8.6 or higher version, First, install the CH340 driver, then follow this selection path in IDE: Tools -  Board "Nano" Processor "ATmega328P", otherwise you'll find that you can't burn any program. 

  • Microcontroller: ATmega328P-MU QFN32
  • Bootloader: Newest 1.8.8
  • Wireless: Nrf24L01+ 2.4G
  • BLE chip: TI CC2540
  • Work channel: 2.4G
  • Transmission distance: 50m
  • Architecture: AVR
  • Input voltage: USB power supply, Vin 6-12V
  • Operating Voltage: 5V
  • Flash Memory: 32KB of which 2KB used by bootloader
  • SRAM: 2KB
  • Clock Speed: 16MHz
  • Analog I/O Pins: 8
  • EEPROM: 1KB
  • DC Current per I/O Pins: 40mA (I/O Pins)
  • Input Voltage: 7-12V
  • Digital I/O Pins: 12
  • PWM Output: 6
  • Power Consumption: 19mA
  • Interface: Micro-USB
  • Pin: Two Lines 2.54mm-15Pin
  • Dimensions: 48x19x12mm
  • Weight: 9g






  • It is fully compatible with the nano-v3.0 pin and its usage method
  • Supports AT directive to configure BLE
  • Support USB virtual serial port, hardware serial port, BLE three-way transparent transmission
  • Support master and slave switch
  • Supports sending over 20byte.
  • Supports iBeacons

Εγγύηση
Ως εξάρτημα, δεν καλύπτεται
Κατασκευαστής
Oem
Καθ. Βάρος
0.002kg
Βρες Παρόμοια
  • Προτείνουμε επίσης