>>> Θέσεις εργασίας <<<

Σημαντική ενημέρωση: Προτείνουμε αλλαγή κωδικού για την ασφάλειά σας (οι κωδικοί χρησιμοποιούν πολύ ασφαλή μέθοδο κρυπτογράφησης)

Στις 22/5 σημειώθηκε μη εξουσιοδοτημένη πρόσβαση στο κατάστημά μας. Μάθετε περισσότερα εδώ.

 
+302118004320
Greek (GR)
0Στο Καλαθι

3D Printer Controller Board 32 Bit - SKR V1.4

59-00018839
ΚατασκευαστήςBIQU
Εξαντλημένο
€3490
Ποσοτικές εκπτώσεις:
Ποσότητα
10+
Τιμή
€31.41
Αγαπημένα
Κάνε μια ερώτηση
Gropbotronics Store Availability
Διαθεσιμότητα Καταστημάτων
Πληρωμή & Μεταφορικά

SKR V1.4 motherboard uses 32-bit main frequency 100MHz ARM-class Cortex-M3 series LPC1768 master chip. Four-Layer Circuit Board, Gold deposition technology,and obtain CE certification. Equipped with highly modular and open source firmware Marlin2.0 and Smoothieware, it is convenient for users to DIY and secondary development, and can avoid worries of not mastering the core code. Support I2C, SPI and WiFi interfaces to DIY. The SPI and UART working mode driven by the TMC driver, also having the DIAG pin, which eliminates complex wiring process and can be used by simple unplugging jumper cap. Reserved extended port SERVOS of PWM signal to support BL Touch, Support 2.8-inch and 3.5-inch color touch screens, support 2004 LCD and 12864 LCD. Double z-axis interface, eliminating the trouble of external drive expansion module. Support Resume Printing While Power Off, Filament Break Detection, Automatic Shutdown After Printing and other functions.

 

ΤΟ ΠΑΚΕΤΟ ΠΕΡΙΕΧΕΙ

  • 1x Motherboard SKR V1.4
  • 1x USB cable A to B

 

ΣΗΜΕΙΩΣΕΙΣ

  • When using smoothieware open source firmware, many functions on SKR V1.4, such as 2130SPI, 2208UART, LCD screen and so on, can not be used. Only Malin firmware can show all the functions of SKR V1.4.

  • Item Type: Motherboard
  • Model Number: SKR V1.4
  • Material: 4-layer PCB
  • Input Voltage: DC12V - DC24V
  • Current: 5A - 15A
  • Logic voltage: DC 3.3V
  • Main control chip: LPC1768
  • Microprocessor: ARM cortex-M3 CPU
  • WIFI module: ESP-01S (not included)
  • Appearance size: 110x85mm
  • Motor driver support:
    • TMC5161, TMC5160, TMC2209, TMC2225, TMC2208, TMC2130
    • ST820, LV8729, DRV8825, A4988 etc.
    • Independent external motor drive.
  • Driver working mode support: SPI, UART, STEP/DIR
  • Motor driver interface: X, Y, Z, E0, E1, 5 way (Each has a closed loop drive interface) up to 256 subdivisions
  • Temperature sensor interface: TH0, TH1, TB, 3 channel 100K NTC Temperature
  • Firmware support: Marlin2.0 , Smoothieware
  • Display support: 2.4", 2.8", 3.5" TFT (Support dual mode screen), LCD2004, LCD12864
  • Expand the interface function support:
    • Resume Printing While Power Off, Filament Break Detection,
    • Automatic Shutdown After Printing, Automatic leveling, BL Touch
  • PC communication interface: Square USB, easy to plug, communication baudrate of 115200
  • Recommended software: Cura, Simplify3D, pronterface, Repetier-host, Makerware
  • Support file format: G-code
  • Supported machine architecture: XYZ, delta, kossel, Ultimaker, CoreXY

  • Using 32-bit main frequency 100MHz ARM level Cortex-M3 series LPC1768 main control chip, the performance has been greatly improved
  • Equipped with highly modular and open source firmware Marlin2.0, which is convenient for users to DIY and secondary development
  • Using dedicated power chip M6130, support 12-24V power input
  • Support 2.4, 2.8, 3.5 inch color touch screen, support LCD2004 screen, LCD12864 screen
  • Upgrade and configure the firmware through SD card, which is simple, convenient and efficient
  • The SPI and UART working mode driven by the TMC driver, also having the DIAG pin, which eliminates complex wiring process and can be used by simple unplugging jumper cap
  • Support Resume Printing While Power Off, Filament Break Detection, Automatic Shutdown After Printing and so on
  • High performance MOSFET tube, better heat dissipation effect
  • Using removable fuse makes the replacement process easier
  • Reserved extended port SERVOS and Probe to support BL Touch
  • Support RGB Neopixel light bar
  • Use the power selection design to separate the USB power supply from the switch power supply, effectively avoiding the situation that the USB port of the computer is burnt out due to short circuit
  • The special function interface uses the row needle with conspicuous color, which greatly reduces the error rate of wiring.
  • I2C, SPI and WIFI interfaces are reserved for convenience of DIY
  • Closed-loop drive interface is reserved to reduce the trouble of plug-in switching module
  • Double z-axis interface, eliminating the trouble of external drive expansion module
  • The thermistor interface is protected by a bile capacitor pressurized resistor to enhance the resistance of the interface
  • More fan interfaces: 1 way CNC fan, 3 way normally open fan
  • Plug-in external DC5V power supply module to supply power to TFT screen, BLtouch and Neopixel

Κατασκευαστής
BIQU
Εγγύηση
Ως εξάρτημα, δεν καλύπτεται με εγγύηση
Καθ. Βάρος
0.16kg
Βρες Παρόμοια
  • Προτείνουμε επίσης