ΔΩΡΕΑΝ ΜΕΤΑΦΟΡΙΚΑ για παραγγελίες άνω των 85.00 έως 2kg

3D Printer Controller Board 32 Bit with TMC2209 - SKR E3 V3.0

από BIQU
Είναι η αναβαθμισμένη έκδοση της SKR E3 V3.0 είναι σχεδιασμένη για τους εκτυπωτές Ender 3, με καλύτερη λειτουργία παθητικής ψύξης, πιο αθόρυβη και εξυπνότερη, μπορεί να υποστηρίξει 2 μοτέρ στο Ζ άξονα, έχει αναβαθμισμένο mosfet για το heatbed είναι η τέλεια αντικατάσταση για την αρχική μητρική πλακέτα του εκτυπωτή Ender 3. Υποστηρίζει τις οθόνες αφής 2,8", 3,5" και την στάνταρ οθόνη LCD12864 του εκτυπωτή Ender3. Με ενσωματωμένους stepper drivers TMC2209 σε λειτουργία UART. Εξοπλισμένο με το λογισμικό ανοιχτού κώδικα Marlin2.0, υποστηρίζει BLTouch, stall detection, απενεργοποίηση του εκτυπωτή και άλλες λειτουργίες.
59-00018844
Ογκομετρικό βάρος: 0.1kg
Εγγύηση: Ως εξάρτημα, δεν καλύπτεται
Κατασκευαστής: BIQU
Χώρα Προέλευσης: Κίνα
Εξαντλημένο
Το προϊόν δεν είναι διαθέσιμο
Χωρίς απόθεμα στο φυσικό κατάστημα
59.90
Χωρίς ΦΠΑ 48.31

Συναινώ ώστε η εταιρεία (GRobotronics) να προσθέσει την διεύθυνση ηλεκτρονικού μου ταχυδρομείου στην λίστα ώστε να λάβω ενημέρωση όταν το προϊόν θα είναι ξανά διαθέσιμο. Μόλις το προϊόν γίνει ξανά διαθέσιμο θα λάβω αυτόματα ενημέρωση στο email αυτό και αμέσως θα αφαιρεθεί από την συγκεκριμένη λίστα.

Το email σου θα χρησιμοποιηθεί αποκλειστικά για τον σκοπό αυτό και καμία άλλη ενημέρωση δεν θα λάβεις. Θα είναι ορατό μόνο από συγκεκριμένους εξουσιοδοτημένους υπαλλήλους της εταιρείας.

Έχετε το δικαίωμα σε περίπτωση κατά την οποία θεωρείτε ότι η επεξεργασία που γίνεται δεν είναι σύμφωνη με τα ανωτέρω να αναζητείτε την προστασία της Αρχής Προσωπικών Δεδομένων και να ζητήσεις να διαγράψουμε ή να μεταβάλλουμε τα δεδομένα σου. Είμαστε υποχρεωμένοι σύμφωνα με τον κανονισμό της ΕΕ για την Προστασία των Γενικών Προσωπικών Δεδομένων να σε ενημερώσουμε για αυτό το δικαίωμα. Έχετε την δυνατότητα να επικοινωνείτε όποτε επιθυμείτε με την εταιρεία ώστε να ενημερωνόσαστε σχετικά με τα προσωπικά σας δεδομένα στο email [email protected]

ΑΓΑΠΗΜΕΝΑ ΣΥΓΚΡΙΣΗ

ΠΕΡΙΓΡΑΦΗ

BIGTREETECH SKR MINI E3 V3.0 Controller Board, New Upgrade Silent Board for Ender 3 3D Printer. Increase the powerful cooling function, quieter and smarter. Look hot! Keeps cool!

Is a simple upgrade for the Creality Ender and CR-10 series. Compared to the original 8-bit motherboard, the stronger 32-bit SKR MINI E3 V3.0 motherboard has much higher performance and more interfaces for DIY modifications.

The motherboard was specially created for a trouble-free upgrade and can be used very easily instead of the original.

In contrast to the previous version, the SKR MINI E3 V3.0 is hardware upgraded and is no longer only compatible with the Ender 3, but also with Ender 5, Ender 5 Pro, CR-10S/S4/S5 3D printers.

Compatible Screens:

  • BTT TFT touchscreens: 2.4 / 3.5 inches
  • LCD12864 (original LCD screen from Creality)

Fan Connectors

  • 3 x controllable CNC fans

Other Interesting Interfaces

  • Module for BLTouch, TFT touchscreen, Neopixel LED strips
  • 5V power interface
  • RGB interface
  • Automatic shutdown after printing
  • Power failure detection module
  • Filament sensor
  • BLTouch interface
  • Dual Z-axis interface
  • Micro USB port

Other Features:

  • MCU: ARM Cortex M0 + STM32G0B1RET6
  • Motor driver: UART mode on-board TMC2209
  • High-performance MOSFET for better heat dissipation
  • Improved thermal performance
  • On-board sensorless homing function
  • Protected thermistor connections
  • 32-bit mainboard
  • Improved performance
  • More stable pressure
  • Easy exchange
  • Recommended software: Cura, Simplify 3D, pronterface, Repetier-host, Makerware

ΤΟ ΠΑΚΕΤΟ ΠΕΡΙΕΧΕΙ

  • 1x Motherboard SKR E3 V3.0
  • 1x USB cable A to B
  • 5x Jumper Pins

 

ΣΗΜΕΙΩΣΕΙΣ

  • This product is a motherboard specially designed for Ender3 printers. For use on other printers, please refer to the corresponding electrical parameters of Ender3 (such as hot bed power,heating rod power, etc.), must not exceed the Ender3 machine electrical.
  • The LCD screen only supports the LCD12864 screen of CR10_STOCKDISPLAY interface.
  • On initial use, the SD card must have a firmware.bin file installed on it prior to powering up. This will install firmware onto the board and allow your computer to recognize it as a USB device.
  • Included on-board stepper drivers TMC2209.

ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

Εγγύηση:
Ως εξάρτημα, δεν καλύπτεται
Κατασκευαστής
:
BIQU
Μικτό Βάρος:
0.1kg
Χώρα Προέλευσης:
Κίνα

ΕΠΙΠΛΕΟΝ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

  • Material: 4-layer PCB
  • MPU: ARM Cortex-M0+ STM32G0B1RET6
  • Main Control Chip: LPC1768
  • Input Voltage: DC12V-DC24V
  • Logic Voltage: 3.3V
  • Current: 5A-15A
  • Support Display:  
    • 2.4" TFT
    • 3.5" TFT
    • Ender3 original LCD12864
  • Removable Fuses
  • Motor Driver: Integrated TMC2209-UART
  • Motor Drive Interface: XM, YM, ZAM, ZBM, EM, 5 channel
  • Support file format: G-code
  • Temperature Sensor Interface:
    • TH0
    • THB
    • 2 channel 100K NTC (thermal resistance)
  • Dimensions: 100x70.25mm
  • Compitable: Ender3, Ender5, CR-10 Printer
  • PC communication interface: USB Micro B type
  • Recommended software: Cura, Simplify 3D, Pronterface, Makerware

 

ΔΥΝΑΤΟΤΗΤΕΣ

Main Control ChipAdopt STMicroelectronics' latest G0 series main control chip STM32G0B1RET6.

Three CNC FanIncrease the heat dissipation controllable fan to reduce the printer temperature when the device is working.

Increased Heat SinkRedesign the drive heat sink, strengthen the drive heat dissipation capacity, and greatly improve the heat dissipation performance.

USB Micro BThe PC communication USB interface is upgraded from Mini USB to Micro USB B, which is more adaptable.

Output Power SupplyIncrease SPI output port +3.3V power supply, external SPI sensor power supply voltage +3.3V and +5V are optional, support the motherboard to directly supply power to peripherals.

ΑΡΧΕΙΑ

ΒΙΝΤΕΟ

Meet All-new Motherboard BIGTREETECH SKR MINI E3 V3 0

Features: ✔ Large, custom-designed heatsink for better heat dissipation ✔ Marlin & Klipper Support ✔ 3 PWM fans ports ✔ Next Gen MCU ✔ Thermistor short circuit protection ✔ 5V and 3.3V outputs available via SPI header ✔ USB Micro Interface ✔Advanced ESD protection on the USB and SD inputs ✔ Fits perfectly into Ender 3, Ender 3Pro, Ender 5, CR 10