Arduino MKR ZERO

02-00010374
ABX00012
CompanyArduino Part NumberABX00012
In Stock
Ships in 24 Hours
3290
Our quantity discounts:
Quantity
10+
Price
31.26
Gropbotronics Store Availability
Availability in Retail Store
Payments & Shipping

The MKR ZERO brings you the power of a Zero in the smaller format established by the MKR form factor. The MKR ZERO board acts as a great educational tool for learning about 32-bit application development. It has an on-board SD connector with dedicated SPI interfaces (SPI1) that allows you to play with MUSIC files with no extra hardware!  The board is powered by Atmel’s SAMD21 MCU, which features a 32-bit ARM Cortex® M0+ core.

The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it by a LiPo battery. The battery voltage can also be monitored since a connection between the battery and the analog converter of the board exists.

 

NOTES

  • Unlike most Arduino & Genuino boards, the MKRZero runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board.
  • DO NOT CONNECT to the male JST connector present on the board anything else than a Li-Po battery whose characteristics are compliant with those indicated above. Please DO NOT POWER VIN with more than 5V.

  • Analog Output Pins: 1 (DAC 10 bit)
  • External Interrupts: 8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17)
  • UART: 1
  • SPI: 1
  • I2C: 1
  • Supported Battery: Li-Po single cell, 3.7V, 700mAh minimum
  • Full-Speed USB Device and embedded Host
  • Flash Memory for Bootloader: 8 KB
  • EEPROM: no
  • LED_BUILTIN: 32

On-board SD

The on- board SD connector allows you to play with files without adding any extra hardware to the board. Furthermore SD card is driven by a dedicated SPI interface (SPI1) and so any of the pins of the header is busy during SD usage. The SD library automatically recognizes the MKR ZERO and so any modification to the sketch is needed to use it aprat from choosing the right SS pin (SDCARD_SS_PIN). 

Battery capacity 

Li-Po batteries are charged up to 4,2V with a current that is usually half of the nominal capacity (C/2). For Arduino MKR ZERO we use a specialized chip that has a preset charging current of 350mAh. This means that the MINIMUM capacity of the Li-Po battery should be 700 mAh. Smaller cells will be damaged by this current and may overheat, develop internal gasses and explode, setting on fire the surroundings. We strongly recommend that you select a Li-Po battery of at least 700mAh capacity. A bigger cell will take more time to charge, but won't be harmed or overheated. The chip is programmed with 4 hours of charging time, then it goes into automatic sleep mode. This will limit the amount of charge to max 1400 mAh per charging round. 

Battery connector 

If you want to connect a battery to your MKRZero be sure to search one with female 2 pin JST PHR2 Type connector.  Polarity : looking at the board connector pins, polarity is Left = Positive, Right = GND  Connector datasheet  On the MKRZero, connector is a Male 2pin JST PH Type 

Additional I2C Port 

The MKRZero has an additional connector meant as an extension of the I2C bus. It's a small form factor 5-pin connector with 1.0mm pitch. The mechanical details of the connector can be found in the connector datasheet.  The I2C port in addition to the SDA and SCL signals includes the GND and +5V power rails and a digital pin that might be useful when designing an expansion.  The pinout is shown in the following image:  

Vin

This pin can be used to power the board with a regulated 5V source. If the power is fed through this pin, the USB power source is disconnected. This is the only way you can supply 5v (range is 5V to maximum 6V) to the board not using USB. This pin is an INPUT. 

5V 

This pin outputs 5V from the the board when powered from the USB connector or from the VIN pin of the board. It is unregulated and the voltage is taken directly from the inputs. As an OUTPUT, it should not be used as an input pin to power the board. 

VCC 

This pin outputs 3.3V through the on-board voltage regulator. This voltage is the same regardless the power source used (USB, Vin and Battery). 

LED ON 

This LED is connected to the 5V input from either USB or VIN. It is not connected to the battery power. This means that it lits up when power is from USB or VIN, but stays off when the board is running on battery power. This maximizes the usage of the energy stored in the battery. It is therefore normal to have the board properly running on battery power without the LED ON being lit. 

CHARGE LED

The CHARGE LED on the board is driven by the charger chip that monitors the current drawn by the Li-Po battery while charging. Usually it will lit up when the board gets 5V from VIN or USB and the chip starts charging the Li-Po battery connected to the JST connector.  There are several occasions where this LED will start to blink at a frequency of about 2Hz. This flashing is caused by the following conditions maintained for a long time (from 20 to 70 minutes): - No battery is connected to JST connector.  - Overdischarged/damaged battery is connected. It can't be recharged.  - A fully charged battery is put through another unnecessary charging cycle. This is done disconnecting and reconnecting either VIN or the battery itself while VIN is connected. 

Onboard LED 

On MKR ZERO the onboard LED is connected to a dedicated pin (32) and not to 13 as on other boards. It is so suggested to use the LED_BUILTIN define.

  

Warranty
12 Months Manufacturer Warranty
Company
Arduino
G. Weight
0.001kg
Family
Arduino MKR
Series
Arduino Making
Microcontroller
SAMD21 Cortex-M0+ 32bit low power ARM MCU
Operating Voltage
3.3V
Input Voltage
5V
Digital I/O Pins
22
Analog Input Channels
7 (ADC 8/10/12 bit)
PWM Channels
12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19)
DC Current per I/O Pin
7mA
DC Current for 3.3V Pin
600mA
Flash Memory
256 KB
SRAM
32KB
Clock Speed
32.768 kHz (RTC), 48 MHz
Find similar
  • We suggest also