Σημαντική ενημέρωση: Προτείνουμε αλλαγή κωδικού για την ασφάλειά σας (οι κωδικοί χρησιμοποιούν πολύ ασφαλή μέθοδο κρυπτογράφησης)

Στις 22/5 σημειώθηκε μη εξουσιοδοτημένη πρόσβαση στο κατάστημά μας. Μάθετε περισσότερα εδώ.

Αρχική Σελίδα/Ρομποτική/Breakout Boards/Converters/ADS1115 16-Bit ADC - 4 Channel with Programmable Gain Amplifier

ADS1115 16-Bit ADC - 4 Channel with Programmable Gain Amplifier

Κωδικός:

09-00001085

Part Number: ADA1085

ΚατασκευαστήςAdafruit Part NumberADA1085

Διαθέσιμο

Αποστολή σε 24 ώρες

€18⁴⁰

+ −

Κάνε μια ερώτηση

Διαθεσιμότητα Καταστημάτων

Πληρωμή & Μεταφορικά

Περιγραφή
Χαρακτηριστικά

For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1115 provides 16-bit precision at 860 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range. We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 16 bit converter.

The chip's fairly small so it comes on a breakout board with ferrites to keep the AVDD and AGND quiet. Interfacing is done via I2C. The address can be changed to one of four options (see the datasheet table 5) so you can have up to 4 ADS1115's connected on a single 2-wire I2C bus for 16 single ended inputs.

Comes with a bit of 0.1" standard header in case you want to use it with a breadboard or perfboard. Four mounting holes for easy attachment.

To get you going fast, we spun up a custom-made PCB in the STEMMA QT form factor, making it easy to interface with. The STEMMA QT connectors on either side are compatible with the SparkFun Qwiic I2C connectors. This allows you to make solderless connections between your development board and the ADS1115 or to chain it with a wide range of other sensors and accessories using a compatible cable.

ΣΗΜΕΙΩΣΕΙΣ

QT Cable is not included, but we have a variety in the shop.
Revision History:
- As of January 16, 2023 – we've updated this PCB with Adafruit Pinguin to make a lovely and legible silkscreen - you may get the new PCB or the older version with vector fonts - both are identical other than the fancy silkscreen.
- As of June 22, 2022 - we've updated this breakout to be STEMMA QT compatible - that means there's now an easy way to plug-and-play this device without any soldering! The physical shape and pinout have changed a little but overall functionality is identical.

Wide Supply Range: 2.0V to 5.5V
Low Current Consumption:
- Continuous Mode: Only 150µA
- Single-Shot Mode: Auto Shut-Down
Programmable Date Rate: 8SPS to 860SPS
Internal Low-Drift Voltage Reference
Internal Oscillator

Internal PGA
I2C Interface: Pin-Selectable Addresses
Four Single-Ended or Two Differential Inputs
Programmable Comparator
This board/chip uses I2C 7-bit addresses between 0x48-0x4B, selectable with jumpers
Dimensions: 25.4x17.8x4.6mm
Weight: 1.8g