FREE SHIPPING for orders over 85.00

Gravity Analog EMG Sensor by OYMotion

by DFROBOT
This EMG sensor is launched by the cooperation of DFRobot and OYMotion, which can detect sEMG to reflect muscle and neural activities of human. This...
25-00016220
Gross Weight: 0.01kg
Warranty: Δεν καλύπτεται με εγγύση απο τον Κατασκευαστή
Company: DFROBOT
Part Number: SEN0240
Made in: China
Out of Stock
Product out of stock
No stock in retail store
61.40
Without VAT 49.52

We (GRobotronics) will add your email address to a special mailing list for this product. Once the product is in stock, you’ll get an email about it automatically, and your email address will be removed from the product’s mailing list.

The data will be visible to some members of our staff. If you’d like to have your personal data removed, send an email to [email protected].

If you believe that your personal data has been misused, you have the right to lodge a complaint with a supervisory authority. We’re obliged by EU General Data Protection Regulation to let you know about this right; we don’t actually intend to misuse your data.

WISHLIST COMPARE

DESCRIPTION

This EMG sensor is launched by the cooperation of DFRobot and OYMotion, which can detect sEMG to reflect muscle and neural activities of human.

This sensor integrates filtering circuit and amplified circuit. It amplifies minimal sEMG within ±1.5mV 1000 times and depresses noises (especially power frequency interference) by differential input and analog filter circuit. The output signal is analog,which takes 1.5V as the reference voltage. The output voltage range is 0~3.0V. The signal strength depends on the intensity of muscle activities. The output signal waveform indicates the muscle activity and contributes to analyze and research the sEMG. Specifically, we can use Arduino as a controller to detect muscle activities, e.g. check whether the muscle is tense; the muscle strength, etc.

This is an active induction sensor can provide high quality signal collection and it is easy to use. Only simple preparations are needed to apply the module for either static or dynamic areas. Dry electrode is applied to the module and good quality signal are available even without conductive gel. Compared with disposable conductive gel needed by medical electrodes, it is more convenient to use and extend its long-life service. Therefore, it is more suitable for most of users.

Measurements with an analog EMG sensor are noninvasive, convenient and this can be applied in human-computer interactions. With the development of microcontrollers and integrated electric circuits, EMG circuits and sensors have not been applied to traditional medical muscle detection researches but control systems.

THE PACKAGE INCLUDES

  • 1x EMG Dry Electrode Board
  • 1x Wrist Belt
  • 1x Electrode Cable
  • 1x EMG Signal Transmitter Board
  • 1x Gravity Analog Cable 3Pin

Connect EMG Sensor with Arduino

 

NOTES

  • The supply voltage range is 3.3~5.5V; The supply current should not be less than 20mA; The ripple current and disturbance current should be as low as possible. Stabilized DC voltage is recommended.
  • The effective spectrum range is 20Hz~500Hz, and the ADC converter which has higher than 8-bit resolution and 1 kHz frequency are recommended to take samples and digitized to keep original information.
  • Placing the metal dry electrode should consistent with the direction of muscle.
  • The product is not a professional medical device and cannot diagnose and cure disease as an assistant device

SPECIFICATIONS

Warranty:
Δεν καλύπτεται με εγγύση απο τον Κατασκευαστή
Company:
DFROBOT
Part Number:
SEN0240
Gross Weight:
0.01kg
Made in:
China
Sensor Type:
  • Biometrics
Typical Input Voltage:
  • 3.3VDC
  • 5VDC
Interface:
  • Analog

EXTRA SPECS

Signal Transmitter Board
  • Supply Voltage: +3.3V~5.5V
  • Operating Voltage: +3.0V
  • Detection Range: +/-1.5mV
  • Electrode Connector: PJ-342
  • Module Connector: PH2.0-3P
  • Output Voltage: 0~3.0V
  • Operating Temperature: 0~50℃
  • Size: 22x35mm
Dry Electrode Board
  • Electrode Connector: PJ-342
  • Wire Length: 50cm(19.69inch)
  • Plate Size: 22x35mm
  • weight: 36g

FEATURES

  • Metal Dry Electrode: long life, easy to use
  • Differential input, high common mode rejection ratio
  • Low power consumption
  • Single power supply

FILES

WE SUGGEST ALSO