ΔΩΡΕΑΝ ΜΕΤΑΦΟΡΙΚΑ για παραγγελίες άνω των 85.00 έως 2kg

Φορτιστής για Μπαταρία 18650 με Step-Up 5V - USB

από OEM

Αυτός ο φορτιστής για μπαταρία 18650 χρησιμοποιείται για τη φόρτιση και την τροφοδοσία μιας πλακέτας επέκτασης Arduino, ESP8266, ESP32 μέσω της εξόδου USB ή απευθείας χρησιμοποιώντας τις έξι εξόδους (pin συγκόλλησης) που είναι διαθέσιμες σε κάθε πλευρά της πλακέτας (5V ή 3V). Έχει κύκλωμα φόρτισης, προσέξτε τους πόλους της μπαταρία κατά την εγκατάσταση, μην αντιστρέψετε (δεν προστατεύεται από αντίστροφη πολικότητα).

19-00019848
Ογκομετρικό βάρος: 0.03kg
Εγγύηση: Ως εξάρτημα, δεν καλύπτεται
Κατασκευαστής: OEM
Χώρα Προέλευσης: Κίνα
Διαθέσιμο
Αποστολή σε 24 ώρες
Διαθέσιμο στο φυσικό κατάστημα
4.80
Χωρίς ΦΠΑ 3.87
+
Τιμές βάση ποσότητας (Λιανική - Χονδρική):
Ποσότητα 10+
Τιμή 3.84

ΠΕΡΙΓΡΑΦΗ

This 18650 battery shield is used to charge and power an Arduino, ESP8266, ESP32 expansion board via the USB output (type A) or directly using the 6 outputs (soldering pin) available on each side of the board (5V or 3V). The shield has a charging circuit (not protected against polarity inversions).

According to the product designation, this card seems to power a mini PC Raspberry Pi type. It is more an optimization of keywords to be visible in the search results than a real power solution. In theory, it should also allow to power the Raspberry Pi and all other mini PCs (Orange Pi, Banana Pi, Odroid …) that have a USB OTG port. Be careful however to buy a high capacity LiFePO battery. The card has no output to measure the battery charge level. It will therefore be necessary to be careful to measure the service life for a complete charge in order to avoid any sudden stop of the system.

The shield has a fairly basic charge control circuit. It is clear to stay polarity. Any inversion of polarity may cause the destruction of the charging circuit. The board has a micro USB connector to charge the battery.

We can feed a development card or any device with a USB port. For this, we have a type A USB output. The maximum intensity delivered is not indicated. It is probably 4A as the side connectors. We also have 3 connectors to deliver 3V up to 1A and 3 connectors to deliver 5V up to 2A. The 6 connectors are on each side of the board.

 

ΣΗΜΕΙΩΣΕΙΣ

  • This module is suitable for 18650 battery only.
  • This module can be power a raspberry pi and sensor at the same time.
  • This module output current up to 2A.
  • This product does not contain 18650 battery installation, be careful of the battery positive and negative when install, do not reverse. Please follow the + - direction on the PCB and do not follow the positive and negative directions on the battery holder.

ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

Εγγύηση:
Ως εξάρτημα, δεν καλύπτεται
Είδος Περιφερειακού:
  • Step-Up
Κατασκευαστής
:
OEM
Τάση Εισόδου:
5-8Volt
Τάση Εξόδου:
5Volt
Ένταση Εξόδου:
3Amp
Μικτό Βάρος:
0.025kg
Χώρα Προέλευσης:
Κίνα
Χημική Σύσταση:
  • Lithium-Ion (Li-Ion)
Τύπος Μπαταρίας:
  • 18650
Υποδοχές Mπαταριών:
1

ΕΠΙΠΛΕΟΝ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

  • Power supply: 5 to 8V via micro USB port up to 0.5A
  • Output power
    • 5V via USB Type A port
    • 3 connectors to deliver 3V up to 1A
    • 3 connectors to deliver 5V up to 2A
  • Misc:
    • 1 USB output
    • LED for the state of charge (green=battery charged, red=charging)
  • Battery protection (overcharging or over-discharging). Attention, no protection in case of reverse polarity
  • Dimensions: 106x29x17mm