FREE SHIPPING for orders over 85.00

Pololu Stepper Motor Driver MP6500

by POLOLU
This breakout board for the MPS MP6500 microstepping bipolar stepper motor driver has a pinout and interface that are very similar to that of our popular...
12-00012966
Gross Weight: 0kg
Warranty: Δεν καλύπτεται με εγγύση απο τον Κατασκευαστή
Company: POLOLU
Part Number: 2966
Made in: USA
Out of Stock
Product out of stock
No stock in retail store
14.80
Without VAT 11.94

We (GRobotronics) will add your email address to a special mailing list for this product. Once the product is in stock, you’ll get an email about it automatically, and your email address will be removed from the product’s mailing list.

The data will be visible to some members of our staff. If you’d like to have your personal data removed, send an email to [email protected].

If you believe that your personal data has been misused, you have the right to lodge a complaint with a supervisory authority. We’re obliged by EU General Data Protection Regulation to let you know about this right; we don’t actually intend to misuse your data.

WISHLIST COMPARE

DESCRIPTION

This breakout board for the MPS MP6500 microstepping bipolar stepper motor driver has a pinout and interface that are very similar to that of our popular A4988 carriers, so it can be used as a drop-in replacement for those boards in many applications. The MP6500 offers up to 1/8-step microstepping, operates from 4.5 V to 35 V, and can deliver up to approximately 1.5 A per phase continuously without a heat sink or forced air flow (up to 2.5 A peak).

This version of the board uses an on-board trimmer potentiometer for setting the current limit, and the board ships with 0.1″ male header pins included but not soldered in.

 

This product is a carrier board or breakout board for the MP6500 stepper motor driver from Monolithic Power Systems (MPS); we therefore recommend careful reading of the MP6500 datasheet (1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to approximately 1.5 A per phase continuously without a heat sink or forced air flow (see the Power dissipation considerations section below for more information). Here are some of the driver’s key features:

  • Simple step and direction control interface
  • Four different step resolutions: full-step, half-step, 1/4-step, and 1/8-step
  • Adjustable current control lets you set the maximum current output, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
  • Potentiometer Current Control uses an on-board trimmer potentiometer to set the current limit up to 2.5 A
  • Internal current sensing allows the driver to automatically adjust the decay mode as necessary to provide the smoothest current waveform
  • 4.5 V to 35 V supply voltage range
  • Can deliver 1.5 A per phase continuously without additional cooling
  • Built-in regulator (no external logic voltage supply needed)
  • Can interface directly with 3.3 V and 5 V systems
  • Over-temperature thermal shutdown, over-current shutdown, short circuit protection, and under-voltage lockout
  • 4-layer, 2 oz copper PCB for improved heat dissipation
  • Exposed solderable ground pad below the driver IC on the bottom of the PCB
  • Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects

SPECIFICATIONS

Warranty:
Δεν καλύπτεται με εγγύση απο τον Κατασκευαστή
Company:
POLOLU
Part Number:
2966
Gross Weight:
0.001kg
Made in:
USA
Driver Type:
  • Stepper
Max. Current per Channel:
2.5A

EXTRA SPECS

  • Minimum operating voltage: 4.5 V
  • Maximum operating voltage: 35 V
  • Continuous current per phase: 1.5 A
  • Maximum current per phase: 2.5 A
  • Minimum logic voltage: 2.1 V
  • Maximum logic voltage: 6 V
  • Microstep resolutions: Full, 1/2, 1/4, and 1/8
  • Current limit control: Potentiometer
  • Dimensions: 20.5x15.5mm
  • Weight: 1.4g

 

WE SUGGEST ALSO