ΔΩΡΕΑΝ ΜΕΤΑΦΟΡΙΚΑ για παραγγελίες άνω των 85.00 έως 2kg

Waveshare MAX-7Q GNSS HAT

από WAVESHARE
Αυτό είναι ένα Raspberry Pi GNSS HAT βασισμένο στο MAX-7Q, το οποίο υποστηρίζει συστήματα εντοπισμού θέσης, όπως GPS, GLONASS, QZSS και SBAS. Διαθέτει ακριβή και γρήγορη τοποθέτηση με μικρές μετατοπίσεις, χαμηλή κατανάλωση ενέργειας, εξαιρετική ικανότητα κατά της πλαστογράφησης & κατά της εμπλοκής κ.λπ. Απλώς προσαρτώντας το στο Pi, είναι αρκετά εύκολο να ενεργοποιήσετε τη δυνατότητα GNSS για το Raspberry Pi σας.
31-00018234
Ογκομετρικό βάρος: 0.16kg
Εγγύηση: Ως εξάρτημα, δεν καλύπτεται
Κατασκευαστής: WAVESHARE
Part Number: MAX-7Q GNSS HAT
Χώρα Προέλευσης: Κίνα
Διαθέσιμο
Αποστολή σε 24 ώρες
Χωρίς απόθεμα στο φυσικό κατάστημα
39.90
Χωρίς ΦΠΑ 32.18
+
Τιμές βάση ποσότητας (Λιανική - Χονδρική):
Ποσότητα 10+
Τιμή 35.91

ΠΕΡΙΓΡΑΦΗ

GNSS Module Based On MAX-7Q For Raspberry Pi

Accurate & Fast Positioning With Minor Drifting, Low Power Consumption, Outstanding Ability For Anti-Spoofing & Anti-Jamming
This is a Raspberry Pi GNSS HAT based on MAX-7Q, which supports positioning systems including GPS, GLONASS, QZSS, and SBAS. It features accurate & fast positioning with minor drifting, low power consumption, outstanding ability for anti-spoofing & anti-jamming, and so on.

By simply attaching it onto the Pi, it is fairly easy to enable GNSS capability for your Raspberry Pi.

ΤΟ ΠΑΚΕΤΟ ΠΕΡΙΕΧΕΙ

  1. MAX-7Q GNSS HAT x1
  2. GPS External Antenna (B) x1
  3. USB-A to Micro-B cable x1
  4. RPi screws pack (2pcs) x1
  5. 2x20PIN female header x1

12345

What's On Board

  1. MAX-7Q module
  2. TXS0108EPWR voltage translator
  3. RT9193-33 power chip
  4. CP2102 USB TO UART converter
  5. Status indicatorsRXD/TXD: UART TX/RX indicatorPPS: GPS status indicatorPWR: power indicator
  6. Battery holdersupports ML1220 rechargeable cell, for preserving ephemeris information and hot starts
  1. Raspberry Pi GPIO headerfor connecting with Raspberry Pi
  2. UART, I2C interfacefor connecting with other MCUs
  3. USB TO UART port
  4. GNSS antenna connector
  5. UART selection jumperA: control the MAX-7Q through USB TO UARTB: control the MAX-7Q through Raspberry PiC: access Raspberry Pi through USB TO UART

ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

Εγγύηση:
Ως εξάρτημα, δεν καλύπτεται
Τύπος HAT:
  • Wireless Communication
Κατασκευαστής
:
WAVESHARE
Part Number:
MAX-7Q GNSS HAT
Μικτό Βάρος:
0.159kg
Χώρα Προέλευσης:
Κίνα
Συμβατό Raspberry:
  • Model 4 B
  • Model 3 B+
  • Model 3 B
  • Model 3 A+
  • Model 2 B
  • Zero
  • Zero W

ΕΠΙΠΛΕΟΝ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

GNSS SPECIFICATIONS
MAX-7Q GPS GLONASS
Frequency band 56x u-blox 7 engine channels
GPS/QZSS L1C/A, GLONASS L1 FDMA, SBAS (WAAS, EGNOS, MSAS)
Horizontal positioning accuracy Autonomous 2.5m CEP 4.0m CEP
SBAS 2.0m CEP -
Max navigation update rate 10Hz 10Hz
Time-To-First-Fix Cold starts 29s 30s
Warm starts 28s 25s
Hot starts 1s 1s
Aided starts 5s -
Sensitivity Tracking and navigating -161 dBm -158 dBm
Re-acquisition -160 dBm -156 dBm
Cold starts -148 dBm -140 dBm
Warm starts -148 dBm -145 dBm
Hot starts -156 dBm -156 dBm
PPS accuracy RMS 30ns 50ns
99% 60ns 100ns
PPS frequency 0.25Hz…10MHz (configurable)
Velocity accuracy 0.1m/s
Heading accuracy 0.5 degree
Operational limits Acceleration (max): 4g
Altitude (max): 50000m
Velocity (max): 500m/s

OTHER SPECIFICATIONS
Communication interface UART (4800~921600bps, 9600bps by default), I2C (max 400KHz)
Update rate 1Hz (default), 10Hz (max)
Protocol NMEA 0183 Version 2.3 (V3.0 compatible), UBX, RTCM 2.3
Power supply 5V
Overall current <37mA@5V (Continue mode)
Module current 17.5mA@3V (Continue mode, tracking status)
Operating temperature -40℃ ~ 85℃
Dimensions 65mm × 30.5mm

ΔΥΝΑΤΟΤΗΤΕΣ

  • Supports GPS/QZSS, GLONASS positioning systems
  • A-GNSS (Assisted GNSS) support, reducing the first positioning time when powered up, improving the acquisition sensitivity
  • Outstanding ability for anti-spoofing & anti-jamming, supports geo-fencing
  • Supports U-Center, an easy way to config the module
  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
  • Onboard USB TO UART converter CP2102 for serial debugging
  • Breakouts the module's UART and I2C interface, for connecting with host boards like Arduino/STM32
  • Baudrate range: 4800~921600bps (9600bps by default)
  • Supports DDC (I2C compliant) interface: up to 400KHz (max)
  • Onboard battery holder, supports ML1220 rechargeable cell, for preserving ephemeris information and hot starts
  • 4x LEDs for indicating the module operating status
  • Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32)

Pinout Definition